Age of Water - User contributions [en]

Document PIHM manual calibration

2014-02-04T00:38:42Z

Steven:

[[Category:Task]]

"Manual calibration" of PIHM is a semi-automated procedure consisting of 3 steps: calibration of parameters controlling lateral groundwater flow, calibration of parameters controlling infiltration, and offline calibration of a simple temperature index model of snow accumulation and melt. These steps are summarized below.

==Parameters controlling lateral groundwater flow==

Parameters controlling lateral groundwater flow include horizontal saturated hydraulic conductivity, KsatH, horizontal macropore hydraulic conductivity, MacKsatH, and macropore depth, MacD. [[File:Jepsen_sample_recession_calib_results.jpg|200px|thumb|right|FIGURE 1. Examples of of PIHM-modeled versus observed (from power law) streamflow recession.]] The soil thickness, to which groundwater flow is also sensitive, is held at an assumed value/distribution. Models are run forward in time from an initial state of completely saturated soil using all meteorological forcings (with precipitation set to zero) to capture the steepening effect of ET on the slope of the recession curve. RMS errors are minimized between modeled stream discharge (base flow) and observed values. The "observed" stream discharge is taken to be the time-dependent solution to the power law -dQ/dt = a*Q^b that best fits observation. Figure 1 (right) illustrates how the different parameters impact the shape of the modeled recession curve. The model calibration runs are executed using in-house Python scripts, and consist of all combinations of the above three parameters in 10 divisions (1000 runs per set). Generally two sets are carried out per calibration, yielding 2000 runs total per calibration.

==Parameters controlling infiltration==

Methods presently under development.

==Temperature index snow accumulation and melt model==

We are presently using a simple model of spatially uniform snow accumulation and melt within the 1 km^2 catchment of our study area. [[File:2010_UpperProv_SWEmodTindex.jpg|200px|thumb|right|FIGURE 2. Modeled snow water equivalent using a temperature-index model compared to observations at a nearby snow pillow.]] We may add spatial variability in snow accumulation and melt at a later stage in this analysis, depending on our later objectives. The model uses the temperature index method, described in Kumar (2009, p. 100), consisting of 4 parameters: 2 parameters controlling the partitioning of new precipitation between snowfall and rainfall [Ts and Tr (deg C)], a parameter controlling the air temperature at which melt begins, and a parameter controlling the increase in melt rate with air temperature (m day^-1 degC^-1). These parameters are determined in an external Excel spreadsheet using a routine, solved with the Solver add-in, that minimizes the RMS error between the time series of modeled and observed snow water equivalent (SWE) (snow pillow). We are able to separate out the snow model from PIHM this way because of the independence between snowmelt and hydrologic fluxes in the modeling framework. We generally obtain RMS errors ranging between 2 and 4 cm SWE (Figure 2). We incorporated into PIHM the accumulation parameters Tr and Ts as calibration parameters in order to fine tune our calibrations. Figure 2 shows model results for full modeled SWE (100%) and 50% modeled SWE, the latter produced by setting Tr and Ts to values of -4.4 deg C.

==References==

Kumar, M. (2009). Toward a hydrologic modeling system. Doctoral dissertation, The Pennsylvania State University, 273 p.



{{#set:
Led by=Tom_Harmon |
Led by=Steve_Jepsen }}

File:Jepsen sample recession calib results.jpg

2014-02-04T00:33:02Z

Steven: Steven uploaded a new version of "File:Jepsen sample recession calib results.jpg": Reverted to version as of 00:30, 4 February 2014

Streamflow recession based on observations (power law) and the PIHM model.

File:Jepsen sample recession calib results.jpg

2014-02-04T00:32:13Z

Steven: Steven uploaded a new version of "File:Jepsen sample recession calib results.jpg": Reverted to version as of 20:06, 3 February 2014

Streamflow recession based on observations (power law) and the PIHM model.

Document PIHM manual calibration

2014-02-04T00:31:49Z

Steven:

[[Category:Task]]

"Manual calibration" of PIHM is a semi-automated procedure consisting of 3 steps: calibration of parameters controlling lateral groundwater flow, calibration of parameters controlling infiltration, and offline calibration of a simple temperature index model of snow accumulation and melt. These steps are summarized below.

==Parameters controlling lateral groundwater flow==

Parameters controlling lateral groundwater flow include horizontal saturated hydraulic conductivity, KsatH, horizontal macropore hydraulic conductivity, MacKsatH, and macropore depth, MacD. [[File:Jepsen_sample_recession_calib_results.jpg|200px|thumb|right|FIGURE 1. Examples of of PIHM-modeled versus observed (from power law) streamflow recession.]] The soil thickness, to which groundwater flow is also sensitive, is held at an assumed value/distribution. Models are run forward in time from an initial state of completely saturated soil using all meteorological forcings (with precipitation set to zero) to capture the steepening effect of ET on the slope of the recession curve. RMS errors are minimized between modeled stream discharge (base flow) and observed values. The "observed" stream discharge is taken to be the time-dependent solution to the power law -dQ/dt = a*Q^b that best fits observation. Figure 1 (right) illustrates how the different parameters impact the shape of the modeled recession curve. The model calibration runs are executed using in-house Python scripts, and consist of all combinations of the above three parameters in 10 divisions (1000 runs per set). Generally two sets are carried out per calibration, yielding 2000 runs total per calibration.

==Parameters controlling infiltration==

Methods presently under development.

=Temperature index snow accumulation and melt model==

We are presently using a simple model of spatially uniform snow accumulation and melt within the 1 km^2 catchment of our study area. [[File:2010_UpperProv_SWEmodTindex.jpg|200px|thumb|right|FIGURE 2. Modeled snow water equivalent using a temperature-index model compared to observations at a nearby snow pillow.]] We may add spatial variability in snow accumulation and melt at a later stage in this analysis, depending on our later objectives. The model uses the temperature index method, described in Kumar (2009, p. 100), consisting of 4 parameters: 2 parameters controlling the partitioning of new precipitation between snowfall and rainfall [Ts and Tr (deg C)], a parameter controlling the air temperature at which melt begins, and a parameter controlling the increase in melt rate with air temperature (m day^-1 degC^-1). These parameters are determined in an external Excel spreadsheet using a routine, solved with the Solver add-in, that minimizes the RMS error between the time series of modeled and observed snow water equivalent (SWE) (snow pillow). We are able to separate out the snow model from PIHM this way because of the independence between snowmelt and hydrologic fluxes in the modeling framework. We generally obtain RMS errors ranging between 2 and 4 cm SWE (Figure 2). We incorporated into PIHM the accumulation parameters Tr and Ts as calibration parameters in order to fine tune our calibrations. Figure 2 shows model results for full modeled SWE (100%) and 50% modeled SWE, the latter produced by setting Tr and Ts to values of -4.4 deg C.

==References==

Kumar, M. (2009). Toward a hydrologic modeling system. Doctoral dissertation, The Pennsylvania State University, 273 p.



{{#set:
Led by=Tom_Harmon |
Led by=Steve_Jepsen }}

File:Jepsen sample recession calib results.jpg

2014-02-04T00:30:01Z

Steven: Steven uploaded a new version of "File:Jepsen sample recession calib results.jpg": Edited text

Streamflow recession based on observations (power law) and the PIHM model.

Document PIHM manual calibration

2014-02-04T00:24:01Z

Steven:

[[Category:Task]]

"Manual calibration" of PIHM is a semi-automated procedure consisting of 3 steps: calibration of parameters controlling lateral groundwater flow, calibration of parameters controlling infiltration, and offline calibration of a simple temperature index model of snow accumulation and melt. These steps are summarized below.

==Parameters controlling lateral groundwater flow==

Parameters controlling lateral groundwater flow include horizontal saturated hydraulic conductivity, KsatH, horizontal macropore hydraulic conductivity, MacKsatH, and macropore depth, MacD. [[File:Jepsen sample recession calib results.jpg|200px|thumb|right|FIGURE 1. Examples of of PIHM-modeled versus observed (from power law) streamflow recession.]] The soil thickness, to which groundwater flow is also sensitive, is held at an assumed value/distribution. Models are run forward in time from an initial state of completely saturated soil using all meteorological forcings (with precipitation set to zero) to capture the steepening effect of ET on the slope of the recession curve. RMS errors are minimized between modeled stream discharge (base flow) and observed values. The "observed" stream discharge is taken to be the time-dependent solution to the power law -dQ/dt = a*Q^b that best fits observation. Figure 1 (right) illustrates how the different parameters impact the shape of the modeled recession curve. The model calibration runs are executed using in-house Python scripts, and consist of all combinations of the above three parameters in 10 divisions (1000 runs per set). Generally two sets are carried out per calibration, yielding 2000 runs total per calibration.

==Parameters controlling infiltration==

Methods presently under development.

=Temperature index snow accumulation and melt model==

We are presently using a simple model of spatially uniform snow accumulation and melt within the 1 km^2 catchment of our study area. [[File:2010_UpperProv_SWEmodTindex.jpg|200px|thumb|right|FIGURE 2. Modeled snow water equivalent using a temperature-index model compared to observations at a nearby snow pillow.]] We may add spatial variability in snow accumulation and melt at a later stage in this analysis, depending on our later objectives. The model uses the temperature index method, described in Kumar (2009, p. 100), consisting of 4 parameters: 2 parameters controlling the partitioning of new precipitation between snowfall and rainfall [Ts and Tr (deg C)], a parameter controlling the air temperature at which melt begins, and a parameter controlling the increase in melt rate with air temperature (m day^-1 degC^-1). These parameters are determined in an external Excel spreadsheet using a routine, solved with the Solver add-in, that minimizes the RMS error between the time series of modeled and observed snow water equivalent (SWE) (snow pillow). We are able to separate out the snow model from PIHM this way because of the independence between snowmelt and hydrologic fluxes in the modeling framework. We generally obtain RMS errors ranging between 2 and 4 cm SWE (Figure 2). We incorporated into PIHM the accumulation parameters Tr and Ts as calibration parameters in order to fine tune our calibrations. Figure 2 shows model results for full modeled SWE (100%) and 50% modeled SWE, the latter produced by setting Tr and Ts to values of -4.4 deg C.

==References==

Kumar, M. (2009). Toward a hydrologic modeling system. Doctoral dissertation, The Pennsylvania State University, 273 p.



{{#set:
Led by=Tom_Harmon |
Led by=Steve_Jepsen }}

Document PIHM manual calibration

2014-02-04T00:21:17Z

Steven:

[[Category:Task]]

"Manual calibration" of PIHM is a semi-automated procedure consisting of 3 steps: calibration of parameters controlling lateral groundwater flow, calibration of parameters controlling infiltration, and offline calibration of a simple temperature index model of snow accumulation and melt. These steps are summarized below.

==Parameters controlling lateral groundwater flow==

Parameters controlling lateral groundwater flow include horizontal saturated hydraulic conductivity, KsatH, horizontal macropore hydraulic conductivity, MacKsatH, and macropore depth, MacD. The soil thickness, to which groundwater flow is also sensitive, is held at an assumed value/distribution. Models are run forward in time from an initial state of completely saturated soil using all meteorological forcings (with precipitation set to zero) to capture the steepening effect of ET on the slope of the recession curve. RMS errors are minimized between modeled stream discharge (base flow) and observed values. The "observed" stream discharge is taken to be the time-dependent solution to the power law -dQ/dt = a*Q^b that best fits observation. Figure 1 (right) illustrates how the different parameters impact the shape of the modeled recession curve. [[File:Jepsen sample recession calib results.jpg|200px|thumb|right|FIGURE 1. Examples of of PIHM-modeled versus observed (from power law) streamflow recession.]] The model calibration runs are executed using in-house Python scripts, and consist of all combinations of the above three parameters in 10 divisions (1000 runs per set). Generally two sets are carried out per calibration, yielding 2000 runs total per calibration.

==Parameters controlling infiltration==

Presently in development. Will update this section later.

==Temperature index snow accumulation and melt model==

We are presently using a simple model of spatially uniform snow accumulation and melt within the 1 km^2 catchment of our study area. We may add spatial variability in snow accumulation and melt at a later stage in this analysis, depending on our later objectives. The model uses the temperature index method, described in Kumar (2009, p. 100), consisting of 4 parameters: 2 parameters controlling the partitioning of new precipitation between snowfall and rainfall [Ts and Tr (deg C)], a parameter controlling the air temperature at which melt begins, and a parameter controlling the increase in melt rate with air temperature (m day^-1 degC^-1). These parameters are determined in an external Excel spreadsheet using a routine, solved with the Solver add-in, that minimizes the RMS error between the time series of modeled and observed snow water equivalent (SWE) (snow pillow). We are able to separate out the snow model from PIHM this way because of the independence between snowmelt and hydrologic fluxes in the modeling framework. We generally obtain RMS errors ranging between 2 and 4 cm SWE (Figure 2). [[File:2010_UpperProv_SWEmodTindex.jpg|200px|thumb|right|FIGURE 2. Modeled snow water equivalent using a temperature-index model compared to observations at a nearby snow pillow.]] We incorporated into PIHM the accumulation parameters Tr and Ts as calibration parameters in order to fine tune our calibrations. Figure 2 shows model results for full modeled SWE (100%) and 50% modeled SWE, the latter produced by setting Tr and Ts to values of -4.4 deg C.

==References==

Kumar, M. (2009). Toward a hydrologic modeling system. Doctoral dissertation, The Pennsylvania State University, 273 p.



{{#set:
Led by=Tom_Harmon |
Led by=Steve_Jepsen }}

Document PIHM manual calibration

2014-02-04T00:16:34Z

Steven:

[[Category:Task]]

"Manual calibration" of PIHM is a semi-automated procedure consisting of 3 steps: calibration of parameters controlling lateral groundwater flow, calibration of parameters controlling infiltration, and offline calibration of a simple temperature index model of snow accumulation and melt. These steps are summarized below.

==Parameters controlling lateral groundwater flow==

Parameters controlling lateral groundwater flow include horizontal saturated hydraulic conductivity, KsatH, horizontal macropore hydraulic conductivity, MacKsatH, and macropore depth, MacD. The soil thickness, to which groundwater flow is also sensitive, is held at an assumed value/distribution. Models are run forward in time from an initial state of completely saturated soil using all meteorological forcings (with precipitation set to zero) to capture the steepening effect of ET on the slope of the recession curve. RMS errors are minimized between modeled stream discharge (base flow) and observed values. The "observed" stream discharge is taken to be the time-dependent solution to the power law -dQ/dt = a*Q^b that best fits observation. Figure 1 (right) illustrates how the different parameters impact the shape of the modeled recession curve. [[File:Jepsen sample recession calib results.jpg|200px|thumb|right|FIGURE 1. Examples of of PIHM-modeled versus observed (from power law) streamflow recession.]] The model calibration runs are executed using in-house Python scripts, and consist of all combinations of the above three parameters in 10 divisions (1000 runs per set). Generally two sets are carried out per calibration, yielding 2000 runs total per calibration.

==Parameters controlling infiltration==

Presently in development. Will update this section later.

==Temperature index snow accumulation and melt model

We are presently using a simple model of spatially uniform snow accumulation and melt within the 1 km^2 catchment of our study area. We may add spatial variability in snow accumulation and melt at a later stage in this analysis, depending on our further objectives. The model uses the temperature index method, described in Kumar (2009, p. 100), consisting of 4 parameters: 2 parameters controlling the partitioning of new precipitation between snowfall and rainfall [Ts and Tr (deg C)], 1 parameter controlling the air temperature at which melt begins (T0), and 1 parameter controlling the melt rate with increasing air temperature (m day^-1 degC^-1). These parameters are determined in an external Excel spreadsheet using a routine, solved with the Solver add-in, that minimizes the RMS error between the time series of modeled and observed snow water equivalent (SWE) (snow pillow). We are able to separate out the snow model from PIHM this way because of the independence between snowmelt and hydrologic fluxes in the modeling framework. We generally obtain RMS errors ranging between 2 and 4 cm SWE (Figure 2). [[File:2010_UpperProv_SWEmodTindex.jpg|200px|thumb|right|FIGURE 2. Modeled snow water equivalent using a temperature-index model compared to observations at a nearby snow pillow.]] We incorporated into PIHM the accumulation parameters Tr and Ts as calibration parameters in order to fine tune our calibrations. Figure 2 shows model results for full modeled SWE (100%) and 50% modeled SWE, the latter produced by setting Tr and Ts to values of -4.4 deg C.

==References==

Kumar, M. (2009). Toward a hydrologic modeling system. Doctoral dissertation, The Pennsylvania State University, 273 p.



{{#set:
Led by=Tom_Harmon |
Led by=Steve_Jepsen }}

File:2010 UpperProv SWEmodTindex.jpg

2014-02-03T23:56:17Z

Steven: Modeled and observed snow water equivalent during water year 2010 at upper Providence catchment.

Modeled and observed snow water equivalent during water year 2010 at upper Providence catchment.

Document PIHM manual calibration

2014-02-03T22:32:00Z

Steven:

[[Category:Task]]

"Manual calibration" of PIHM is a semi-automated procedure consists of 3 steps: calibration of parameters controlling lateral groundwater flow, calibration of parameters controlling infiltration, and offline calibration of a simple temperature index model for snow accumulation melt. These steps are summarized below.

==Parameters controlling lateral groundwater flow==

Parameters controlling lateral groundwater flow include the horizontal saturated hydraulic conductivity, KsatH, horizontal macropore hydraulic conductivity, MacKsatH, and macropore depth, MacD. The soil thickness, which groundwater flow is also sensitive, is held at an assumed value/distribution. Models are run forward from an initial state of completely saturated soil using all meteorological forcings (with precipitation set to zero) to capture the steepening effect of ET on the slope of the recession curve. Errors are examined between modeled stream discharge (base flow) and observed. The "observed" stream discharge is taken to be the time-dependent solution to the power law -dQ/dt = a*Q^b that best fits observation. Figure 1 (right) illustrates how the different parameters impact the shape of the modeled recession curve.[[File:Jepsen sample recession calib results.jpg|200px|thumb|right|Examples of of PIHM-modeled versus observed (from power law) stream discharge]] The model calibration runs are executed using in-house Python scripts, and consist of all combinations of the above three parameters divided into 10 divisions (1000 runs per set). Generally two sets are carried out per calibration, yielding 2000 runs per calibration.



{{#set:
Led by=Tom_Harmon |
Led by=Steve_Jepsen }}

Document PIHM manual calibration

2014-02-03T22:20:52Z

Steven:

[[Category:Task]]

Under construction...

Manual calibration of PIHM consists of 3 components: parameters controlling lateral groundwater flow, parameters controlling infiltration, and the snow accumulation / melt model.

==Parameters controlling lateral groundwater flow==

Parameters controlling lateral groundwater flow are taken to be horizontal saturated hydraulic conductivity, KsatH, horizontal macropore hydraulic conductivity, MacKsatH, and macropore depth, MacD. The soil thickness, another important parameter, is held at an assumed value. Models are run forward from an initial state of completely saturated soil using all meteorological forcings (except precipitation) to capture the steepening effect of ET on the slope of the recession curve. The "observation" stream discharge is taken to be the time-dependent solution to the power law that best fits the observed stream hydrograph. The graphic solution below illustrates how the different parameters impact the shape of the modeled recession curve.

[[File:Jepsen sample recession calib results.jpg|200px|thumb|right|Sample of PIHM-modeled versus observed (from power law) stream discharge]]



{{#set:
Led by=Tom_Harmon |
Led by=Steve_Jepsen }}

Document PIHM manual calibration

2014-02-03T21:05:44Z

Steven:

[[Category:Task]]

Under construction...

Manual calibration of PIHM consists of 3 components: parameters controlling lateral groundwater flow, parameters controlling infiltration, and the snow accumulation / melt model.

=Parameters Controlling Lateral Groundwater Flow=

Parameters controlling lateral groundwater flow are taken to be horizontal saturated hydraulic conductivity, KsatH, horizontal macropore hydraulic conductivity, MacKsatH, and macropore depth, MacD. The soil thickness, another important parameter, is held at an assumed value. Models are run forward from an initial state of completely saturated soil using all meteorological forcings (except precipitation) to capture the steepening effect of ET on the slope of the recession curve. The "observation" stream discharge is taken to be the time-dependent solution to the power law that best fits the observed stream hydrograph. The graphic solution below illustrates how the different parameters impact the shape of the modeled recession curve.

[[File:Jepsen sample recession calib results.jpg|200px|thumb|right|Sample of PIHM-modeled versus observed (from power law) stream discharge]]



{{#set:
Led by=Tom_Harmon |
Led by=Steve_Jepsen }}

Document PIHM manual calibration

2014-02-03T21:02:55Z

Steven:

[[Category:Task]]

Under construction...

Manual calibration of PIHM consists of 3 components: parameters controlling lateral groundwater flow, parameters controlling infiltration, and the snow accumulation / melt model.

=Parameters Controlling Lateral Groundwater Flow=

Parameters controlling lateral groundwater flow are taken to be horizontal saturated hydraulic conductivity, KsatH, horizontal macropore hydraulic conductivity, MacKsatH, and macropore depth, MacD. The soil thickness, another important parameter, is held at an assumed value. Models are run forward from an initial state of completely saturated soil using all meteorological forcings (except precipitation) to capture the steepening effect of ET on the slope of the recession curve. The "observation" stream discharge is taken to be the time-dependent solution to the power law that best fits the observed stream hydrograph. The graphic solution below illustrates how the different parameters impact the shape of the modeled recession curve.

[[File:Jepsen sample recession calib results.jpg|200px|thumb|right|caption]]



{{#set:
Led by=Tom_Harmon |
Led by=Steve_Jepsen }}

Document PIHM manual calibration

2014-02-03T20:58:17Z

Steven:

[[Category:Task]]

Manual calibration of PIHM consists of 3 components: parameters controlling lateral groundwater flow, parameters controlling infiltration, and the snow accumulation / melt model.

=Parameters Controlling Lateral Groundwater Flow=

Parameters controlling lateral groundwater flow are taken to be horizontal saturated hydraulic conductivity, KsatH, horizontal macropore hydraulic conductivity, MacKsatH, and macropore depth, MacD. The soil thickness, another important parameter, is held at an assumed value. Models are run forward from an initial state of completely saturated soil using all meteorological forcings (except precipitation) to capture the steepening effect of ET on the slope of the recession curve. The "observation" stream discharge is taken to be the time-dependent solution to the power law that best fits the observed stream hydrograph. The graphic solution below illustrates how the different parameters impact the shape of the modeled recession curve.

Notes can be added here.



{{#set:
Led by=Tom_Harmon |
Led by=Steve_Jepsen }}

Document PIHM manual calibration

2014-02-03T20:57:36Z

Steven:

[[Category:Task]]

Manual calibration of PIHM consists of 3 components: parameters controlling lateral groundwater flow, parameters controlling infiltration, and the snow accumulation / melt model.

=Parameters Controlling Lateral Groundwater Flow=

Parameters controlling lateral groundwater flow are taken to be horizontal saturated hydraulic conductivity, KsatH, horizontal macropore hydraulic conductivity, MacKsatH, and macropore depth, MacD. The soil thickness, another important parameter, is held at an assumed value. Models are run forward from an initial state of completely saturated soil using all meteorological forcings (except precipitation) to capture the steepening effect of ET on the slope of the recession curve. The "observation" stream discharge is taken to be the time-dependent solution to the power law that best fits the observed stream hydrograph. The graphic solution below illustrates how the different parameters impact the shape of the modeled recession curve.

[[File:Jepsen sample recession calib results.jpg]]

Notes can be added here.



{{#set:
Led by=Tom_Harmon |
Led by=Steve_Jepsen }}

Document PIHM manual calibration

2014-02-03T20:53:33Z

Steven:

[[Category:Task]]

Manual calibration of PIHM consists of 3 components: parameters controlling lateral groundwater flow, parameters controlling infiltration, and the snow accumulation / melt model.

=Parameters Controlling Lateral Groundwater Flow=

Parameters controlling lateral groundwater flow are taken to be horizontal saturated hydraulic conductivity, KsatH, horizontal macropore hydraulic conductivity, MacKsatH, and macropore depth, MacD. The soil thickness, another important parameter, is held at an assumed value. Models are run forward from an initial state of completely saturated soil using all meteorological forcings (except precipitation) to capture the steepening effect of ET on the slope of the recession curve. The "observation" stream discharge is taken to be the time-dependent solution to the power law that best fits the observed stream hydrograph. The graphic solution below illustrates how the different parameters impact the shape of the modeled recession curve.

Graphic

Notes can be added here.



{{#set:
Led by=Tom_Harmon |
Led by=Steve_Jepsen }}

Document PIHM manual calibration

2014-02-03T20:49:54Z

Steven:

[[Category:Task]]

Parameters controlling lateral groundwater flow are taken to be horizontal saturated hydraulic conductivity, KsatH, horizontal macropore hydraulic conductivity, MacKsatH, and macropore depth, MacD. The soil thickness, another important parameter, is held at an assumed value. Models are run forward from an initial state of completely saturated soil using all meteorological forcings (except precipitation) to capture the steepening effect of ET on the slope of the recession curve. The "observation" stream discharge is taken to be the time-dependent solution to the power law that best fits the observed stream hydrograph. The graphic solution below illustrates how the different parameters impact the shape of the modeled recession curve.

Graphic

Notes can be added here.



{{#set:
Led by=Tom_Harmon |
Led by=Steve_Jepsen }}

Document PIHM manual calibration

2014-02-03T20:49:22Z

Steven:

[[Category:Task]]

Parameters controlling lateral groundwater flow are taken to be horizontal saturated hydraulic conductivity, KsatH, horizontal macropore hydraulic conductivity, MacKsatH, and macropore depth, MacD. The soil thickness, another important parameter, is held at an assumed value. Models are run forward from an initial state of completely saturated soil using all meteorological forcings (except precipitation) to capture the steepening effect of ET on the slope of the recession curve. The "observation" stream discharge is taken to be the time-dependent solution to the power law that best fits the observed stream hydrograph. The graphic solution below illustrates how the different parameters impact the shape of the modeled recession curve.

Notes can be added here.



{{#set:
Led by=Tom_Harmon |
Led by=Steve_Jepsen }}

File:Jepsen sample recession calib results.jpg

2014-02-03T20:06:55Z

Steven: Streamflow recession based on observations (power law) and the PIHM model.

Streamflow recession based on observations (power law) and the PIHM model.

Document PIHM manual calibration

2014-02-03T19:36:08Z

Steven: Deleted PropertyValue: SubTask = Testing

[[Category:Task]]

Notes can be added here.



{{#set:
Led by=Tom_Harmon |
Led by=Steve_Jepsen }}

Document PIHM manual calibration

2014-02-03T19:35:55Z

Steven: Added PropertyValue: SubTask = testing

[[Category:Task]]

Notes can be added here.



{{#set:
Led by=Tom_Harmon |
Led by=Steve_Jepsen |
SubTask=Testing }}

Document PIHM manual calibration

2014-02-03T19:35:19Z

Steven: Deleted PropertyValue: Answer = This is now under construction

[[Category:Task]]

Notes can be added here.



{{#set:
Led by=Tom_Harmon |
Led by=Steve_Jepsen }}

Document PIHM manual calibration

2014-02-03T19:34:10Z

Steven: Added PropertyValue: Answer = This is now under construction

[[Category:Task]]

Notes can be added here.



{{#set:
Answer=This_is_now_under_construction |
Led by=Tom_Harmon |
Led by=Steve_Jepsen }}